Plumber's Essentials: What You Need for Bathtub Installation
Plumber's Essentials: What You Need for Bathtub Installation
Blog Article
Do you find yourself hunting for selective information on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Mounting a bath tub isn't specifically rocket science, however it does require strong plumbing, woodworking, and in some cases, tiling abilities. Changing an old bathtub with a brand-new one is also a reasonably challenging task. If the old tub is easily accessible, the project can relocate quickly; if you need to open a wall surface to remove the old bathtub as well as place the new bathtub, the task is much harder. In either instance, the task is within a house handyman's abilities, although you will certainly need an assistant to vacate the old tub and embeded in the new one. Make sure you have certified yourself for the job as well as are comfortable trying it. Rather than working with a specialist to take over a halfway-completed job, it is better to think about utilizing one before you begin. Possibilities are you may need a professional plumber to make tube links.
This post will assist you mount a new tub in your shower room if you have actually currently purchased a new tub and don't need to transform the setup of your previous water system pipelines.
Your devices and product checklist must comprise the following:
Removing Old Taps
If you require to replace old taps with brand-new ones as a part of your installment, then the first thing you need to do is separate the supply of water. After doing so, activate the taps to drain any water staying in the system. The procedure of eliminating the existing taps can be fairly problematic as a result of the limited gain access to that is often the instance.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipes to the taps. Have a towel ready for the staying water that will certainly originate from the pipes. As soon as the supply pipes have actually been removed, make use of the same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary faucets from turning throughout this procedure. As soon as the taps have been eliminated, the holes in the bath/basin will certainly have to be cleaned of any kind of old securing substance.
Prior to carrying on to fit the brand-new taps, compare the pipe connections on the old taps to the brand-new taps. If the old faucets are longer than the brand-new faucets, after that a shank adapter is required for the new taps to fit.
Suitable New Taps
If the tails of the brand-new faucets are plastic, then you will certainly need a plastic port to prevent damage to the string. One end of the adapter fits on the plastic tail of the faucet and also the other end provides a link to the current supply pipes.
If you require to fit a monobloc, then you will require decreasing couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next off, place the tap in the placing hole in the bath/basin ensuring that the washers remain in location between the tap and also the sink. Safeguard the faucet in position with the producer supplied backnut. When the tap is securely in place, the supply pipelines can be linked to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with typical tap connectors. The previous type needs to be attached to the tap ends initially, tightening up only by hand. The supply pipes can later be linked to the various other end. Tighten both ends with a spanner after both ends have been connected.
Installing the Bath tub
Utilizing both wood boards under its feet, put the tub in the needed placement. The wood boards are useful in uniformly spreading out the weight of the bathtub over the location of the boards instead of concentrating all the weight onto 4 little points.
The next objective is to make certain that the bath tub is leveled all round. This can be achieved by inspecting the level and also changing the feet on the bathtub up until the spirit level checks out level.
To mount taps, fit the bottom of the furthest adaptable faucet adapter to the ideal supply pipe by making a compression sign up with; then do the very same for the other tap.
Turn on the water supply and also examine all joints and also brand-new pipework for leaks and also tighten them if required. Load the tub as well as likewise examine the overflow electrical outlet and also the typical electrical outlet for leaks.
Ultimately, fix the bath paneling as defined in the maker's instruction manual. Tiling and sealing around the bath tub should wait up until the bath tub has actually been made use of at least when as this will settle it into its final setting.
Planning for the Installment
First of all, the supporting structure supplied with the bathroom must be fitted (if needed) according to the supplier's guidelines. Next off, fit the taps or mixer to the tub. When fitting the tap block, it is necessary to see to it that if the tap features a plastic washing machine, it is fitted in between the bath as well as the faucets. On a plastic bathroom, it is likewise reasonable to fit a supporting plate under the faucets unit to avoid stress on the bathtub.
Fit the versatile tap connectors to the bottom of the two taps using 2 nuts and also olives (in some cases provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet with the hole in the bath. Make use of the nut provided by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bath. Make certain you make use of all of the supplied washers.
Attach the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bath must currently prepare to be fitted in its final placement.
Tiling Around the Bath tub
In the area where the bath fulfills the floor tile, it is necessary to seal the joins with a silicone rubber caulking. This is very important as the installation can relocate sufficient to fracture an inflexible seal, triggering the water to permeate the wall surface in between the bathroom and also the tiling, leading to difficulties with wetness as well as feasible leaks to the ceiling below.
You can pick from a range of coloured sealers to blend in your components and also installations. They are sold in tubes as well as cartridges, and can sealing voids approximately a width of 3mm (1/8 inch). If you have a bigger void to fill, you can load it with spins of drenched newspaper or soft rope. Bear in mind to constantly fill the bathtub with water prior to sealing, to permit the activity experienced when the bathtub remains in use. The sealant can break fairly very early if you do not take into account this motion before sealing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are likewise easily readily available on the market. It is advisable to fit the tiles making use of waterproof or water resistant glue and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I am just very curious about Installing A Bathtub and I hope you liked the post. Please set aside a second to promote this entry if you appreciated it. I appreciate reading our article about How to Install a Bathtub.
Top service, one call. Report this page